Shako Co Ltd

Removes debris + 90% oil / moisture from compressed air systems.

Coalescing removes all oil + moisture, carbon removes odours + bacteria.

Air pressure regulator + air filter provides stable adjustable outlet pressure and remove debris and 90% oil + moisture.

Air pressure regulator with air filter with air lubrication system. Provides stable outlet pressure whilst removing debris and 90% moisture the finally providing oil mist to lubricate downstream equipment.

Provides lubricating oil by misting system into to lubricate downstream equipment.

Air pressure regulator regulates and provides stable outlet pressure.

air actuated valves that utilise a compressed air supply to operate.

compressed air line tubing and push to connect fittings

Motor and air actuated quarter turn 2+3 way ball valves

Check + non return valves only allow flow in one direction

Automated + time control drain valves

Flow regulating valves with manual or electric modulating 4-20mA control.

3/2 + 5/2 foot pedal air control valves for pneumatic cylinders and systems.

3/2 + 5/2 way air valves controlled by a Finger or Palm Button

Air valves that are controlled manually

3/2 and 5/2 air control valves that require users to twist a button

Air control valves operate with a manual lever. 3/2, 5/2, 5/3, 4/2 + 4/3 way

2/2, 3/2, 5/2 mechanical air control valves for automated pneumatic systems.

Pressure reducing valves (PRV) reduce and maintain stable outlet pressure

Will instantly open outlet to exhaust when the inlet pressure drops to greatly increase cylinder reaction speed.

Safety shut off isolation valve, shuts off and secures air line systems, will vent downstream air when closed.

Incorporates a check ball valve to allow pressure in a line to be obtained from two sources.

Electric open and close control for airline systems, power off downstream air is vented to atmosphere - power on opens slowly to prevent sudden pressure surges.

Valves controlled by electrical signal via a solenoid or electro magnet.

Non Contact Suction Pad uses compressed air to lift without contact.

Time control valves can be set to activate according to preset intervals when power is applied.

Can generate vaccum using compressed air supply up to -91.8 Kpa

valves with 1/8 inch threaded ports

valves with 1/4 inch threaded ports

valves with 3/8 inch threaded ports

valves with 1/2 inch threaded ports

valves with 3/4 inch threaded ports

valves with 1 inch threaded ports

valves with 11/4 inch threaded ports

valves with 11/2 inch threaded ports

valves with 2 inch threaded ports

valves with 21/2 inch threaded ports

valves with 3 inch threaded ports

valves with Namur interface mounting

2 ports (inlet/outlet) with 2 positions (Open/Closed) - valve stays closed (Failsafe) requires power to open

2 ports (inlet/outlet) with 2 positions (Open/Closed) - valve stays open (Failsafe) requires power to close

2 ports (inlet/outlet) with 2 positions (Open/Closed) - short power pulse valve stays open - reverse power pulse valve stays closed

2 ports (inlet/outlet) with 2 positions (Open/Closed) - power or air one side to move - power or air opposite side to return.

3 ports with 2 positions. Power off inlet closed, outlet open to exhaust - power on inlet open to outlet with exhaust closed.

3 ports 2 positions. Inlet open to outlet with exhaust closed - power on inlet closed with outlet open to exhaust.

A 4/2 way valve has four ports and two positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system.

A 4/3 way valve has four ports and three positions. It controls the direction of flow by switching between two paths in a pneumatic or hydraulic system with third option all ports closed.

5 ports 2 positions (1 inlet, 2 outlets, 2 exhaust ports). Power to coil Cylinder fully extends - Power off cylinder fully retracts (or visa versa)

Power to left coil Cylinder fully extends, power to right coil cylinder fully retracts, power off cylinder stays put fully extended or retracted.

Power to left coil cylinder extends, power to right coil cylinder retracts, power off cylinder stays put even in a mid position.

0.02 Bar = 20 millibars = 0.29psi = 2 Kpa

0.1 Bar = 100 millibars = 1.47 psi = 1kPa

0.2 Bar = 200 millibars = 2.94 psi = 20kPa

0.3 Bar = 300 millibars = 4.41 psi = 30 kPa

0.4 Bar = 400 millibars = 4.41 psi = 40 kPa

0.5 Bar = 500 millibars = 7.36 psi = 50 kPa

0.6 Bar = 600 millibars = 8.83 psi = 60 kPa

0.7 Bar = 700 millibars = 10.3 psi = 70 kPa

0.8 Bar = 800 millibars = 11.77 psi = 80 kPa

1 Bar = 1000 millibars = 14.71 psi = 100 kPa = 0.1 MPa

1.2 Bar = 1200 millibars = 17.65 psi = 1200 kPa = 0.12 MPa

1.3 Bar = 1300 millibars = 19.12 psi = 1300 kPa = 0.13 MPa

1.4 Bar = 1400 millibars = 20.59 psi = 1400 kPa = 0.14 MPa

1.5 Bar = 1500 millibars = 22.07 psi = 1500 kPa = 0.15 MPa

1.6 Bar = 1600 millibars = 23.54 psi = 1600 kPa = 0.16 MPa

2 Bar = 2000 millibars = 29.42 psi = 2000 kPa = 0.2 MPa

2.5 Bar = 2500 millibars = 36.78 psi = 2500 kPa = 0.25 MPa

3 Bar = 3000 millibars = 44.13 psi = 3000 kPa = 0.3 MPa

3.5 Bar = 3500 millibars = 51.49 psi = 3500 kPa = 0.35 MPa

4 Bar = 4000 millibars = 58.84 psi = 4000 kPa = 0.4 MPa

4.5 Bar = 4500 millibars = 66.20 psi = 4500 kPa = 0.45 MPa

5 Bar = 5000 millibars = 73.55 psi = 5000 kPa = 0.5 MPa

5.5 Bar = 5500 millibars = 80.91 psi = 5500 kPa = 0.55 MPa

6 Bar = 6000 millibars = 88.26 psi = 6000 kPa = 0.6 MPa

6.5 Bar = 6500 millibars = 95.62 psi = 6500 kPa = 0.65 MPa

7 Bar = 7000 millibars = 102.97 psi = 7000 kPa = 0.7 MPa

7.5 Bar = 7500 millibars = 110.33 psi = 7500 kPa = 0.75 MPa

8 Bar = 8000 millibars = 117.68 psi = 8000 kPa = 0.8 MPa

8.5 Bar = 8500 millibars = 125.04 psi = 8500 kPa = 0.85 MPa

9 Bar = 9000 millibars = 132.39 psi = 9000 kPa = 0.9 MPa

10 Bar = 147.1 psi = 1 MPa

12 Bar = 176.52 psi = 1.2 MPa

13 Bar = 191.23 psi = 1.3 MPa

14 Bar = 205.94 psi = 1.4 MPa

15 Bar = 220.65 psi = 1.5 MPa

16 Bar = 235.36 psi = 1.6 MPa

17 Bar = 250.07 psi = 1.7 MPa

18 Bar = 264.78 psi = 1.8 MPa

20 Bar = 294.2 psi = 2 MPa

25 Bar = 367.8 psi = 2.5 MPa

30 Bar = 441.3 psi = 3 MPa

35 Bar = 514.9 psi = 3.5 MPa

40 Bar = 588.4 psi = 4 MPa

50 Bar = 735.5 psi = 5 MPa

60 Bar = 882.6 psi = 6 MPa

64 Bar = 941.4 psi = 6.4 MPa

EPDM (Ethylene Propylene Diene Monomer) - known as Ethylene Propylene terpolymer, Buna-AP, Dutral, Polysar-EDM, Royalene, Vistalon, Keltan, Epcar, Nordel or Epsyn). Good for hot and drinking water, Steam, Freon refrigerant gas and Air -40°C to +120°C (+150°C steam) Poor resistance to oils + fuels

FKM Fluoro elastomer (Fluorocarbon) Viton® Dupont registered, known as Tecnoflon, Fluorel, Dai-El. Good for hot water, acid, alkali, oils, hydrocarbons and salt solutions, many aggressive chemicals, diluted acids, weak alkali's, mineral oils, aliphatic and aromatic hydrocarbons, chlorinated hydrocarbons, sunlight and ozone. -26°C to +205°C. Poor resistance to Ketone's and Acetone.

HNBR (Hydrogenated Nitrile Butadine Rubber) also known as Therban, Zetpol or Tornac). Good for motor oils, sour gas, amine oil mixtures, oxidised fuels, lubricating oils, mineral based hydraulic oil, animal and vegetable oil, diesel fuel, ozone, dilute acids and bases, new bio-oils, H2S Hydrogen Sulphide and C02 carbon dioxide. -40°C to +150°C. Poor for concentrated alkali's, esters, alkyl phosphate, ethers, halogenated solvents, ketone's, halogenated hydrocarbons, solvents and flames.

NBR (Nitrile Buna Rubber) known as Nitrile Butadine, Buna-N, Hycar, Chemigum, Butakon, Breaon, Butacril, Paracil, Nipol, Perbunan, Krynac or Europrene-N. Good for Aliphatic Hydrocarbons, Petroleum, Fuels, Mineral Oil, Vegetable and Hydraulic Oil, Alcohol and many Acids. -35°C to +100°C. Poor for Ozone, Acetone, Methyl ethyl Ketone, Chlorinated Hydrocarbons, Ethers and Esters.

PTFE (Polytetrafluoroethylene) also known as Teflon® Dupont registered. Excellent resistance to almost every fluid or gas. -200°C to +230°C

3 volts Direct Current for 2x 1.5v AA batteries

6 volts Direct Current

12 volts Direct Current

12 volts 50/60Hz Alternating Current

24 volts Direct Current

24 volts 50/60Hz Alternating Current

36 volts 50/60Hz alternating current

48 volts 50/60Hz alternating current

48 volts Direct Current

110 volts 50/60Hz Alternating Current

110 volts Direct Current

125 volts Direct Current

230 volts 50/60Hz Alternating Current

200 volts Direct Current

380 volts 50/60Hz Alternating Current

hazardous area classification indicating a potentially explosive atmosphere with gases and dust present, requiring specific equipment for safe operation.

certifies equipment for use in potentially explosive atmospheres, indicating it is designed to prevent ignition sources, minimizing risk.

ATEX Protection by encapsulation ll 2 G Ex mb ll T4 Gb and ll 2 D Ex tb IIIC T130°C Db IP65

ATEX protection by intrinsic safety, II 2 G Ex ia IIB/IIC T4 or T6.

Dust protected and protected against splashing water

Dust tight and protected against water jets

EN12021 approval certifies compressed air quality for breathing apparatus, ensuring it meets safety standards for human respiratory use.

FDA approval is the process by which the Food and Drug Administration evaluates and authorizes the marketing of new drugs, medical devices, and biologics for safety and efficacy.

WRAS approval ensures water fittings meet UK water regulations, safeguarding public health by preventing contamination, waste, and misuse of water supplies.

Valve orifice or sealing face with diameter 0.8mm

Valve orifice or sealing face with diameter 1mm

Valve orifice or sealing face with diameter 1.1mm

Valve orifice or sealing face with diameter 1.2mm

Valve orifice or sealing face with diameter 1.4mm

Valve orifice or sealing face with diameter 1.5mm

Valve orifice or sealing face with diameter 1.6mm

Valve orifice or sealing face with diameter 1.8mm

Valve orifice or sealing face with diameter 2mm

Valve orifice or sealing face with diameter 2.2mm

Valve orifice or sealing face with diameter 2.3mm

Valve orifice or sealing face with diameter 2.4mm

Valve orifice or sealing face with diameter 2.5mm

Valve orifice or sealing face with diameter 2.6mm

Valve orifice or sealing face with diameter 3mm

Valve orifice or sealing face with diameter 3.5mm

Valve orifice or sealing face with diameter 4mm

Valve orifice or sealing face with diameter 4.5mm

Valve orifice or sealing face with diameter 5

Valve orifice or sealing face with diameter 5.5mm

Valve orifice or sealing face with diameter 6mm

Valve orifice or sealing face with diameter 6.5mm

Valve orifice or sealing face with diameter 7mm

Valve orifice or sealing face with diameter 7.5

Valve orifice or sealing face with diameter 8mm

Valve orifice or sealing face with diameter 9mm

Valve orifice or sealing face with diameter 9.5mm

Valve orifice or sealing face with diameter 11mm

Valve orifice or sealing face with diameter 12mm

Valve orifice or sealing face with diameter 13mm

Valve orifice or sealing face with diameter 15mm

Valve orifice or sealing face with diameter 20mm

Valve orifice or sealing face with diameter 25mm

Valve orifice or sealing face with diameter 30mm

Valve orifice or sealing face with diameter 32mm

Valve orifice or sealing face with diameter 38mm

Valve orifice or sealing face with diameter 40mm

Valve orifice or sealing face with diameter 50mm

Valve orifice or sealing face with diameter 65mm

Valve orifice or sealing face with diameter 80mm

Assisted lift solenoid valve assists in opening against pressure, ensuring reliable operation from vacuum to medium pressure systems.

Directly controls flow without external pressure assistance operates from vacuum upwards.

Operate via pilot pressure control and require a minimum pressure difference between inlet and outlet from 0.5 Bar.

Prevents or reduces water hammer caused by sudden changes in fast moving fluid flow.

Can control flow in both directions

Oil and grease removed typically for oxygen or paint spray use.

Flow regulation to control the amount of flow.

A group of multiple valves together on one manifold, simple layout streamline control and space saving.

Valves that require manual input to operate such as lever, button or switch

A facility to manually move the valve into the fully actuated position via a button, lever or key.

Valve has the facility to be supplied with a bracket for mounting and securing.

Supplied with additional threaded holes typically in the base, typically for securing to a baseplate.

The outlet port is at right angles to inlet port, ideal for space efficiency.

Outlet port and a Hose tail or barb to connect directly into flexible tube

Valve is designed to be mounted and secured into an instrument panel

The valve is equipped with clear cover or dome under which an arrow or flag can be seen to confirm either the open and or closed position of the valve.

The copper shading ring in the solenoid tube has been replaced with silver. Typically used for RO water and aggressive media applications.

The copper shading ring in the solenoid tube has been removed, for DC voltages only and typically for aggressive media applications.

A unidirectional speed controller regulates fluid or gas flow in one direction only, often used in pneumatic systems for precise control.

A Y-pattern valve is a valve with a Y-shaped body design, typically used for high-pressure applications to reduce pressure drop and turbulence, often found in steam systems.